Calculations

<< Click to Display Table of Contents >>

Navigation:  Chapter 9 Geotechnical Data Management > Geotechnical Tests > Entering Test Data > Soil and Aggregates Tests > Triaxial - Consolidated Undrained >

Calculations

Previous pageReturn to chapter overviewNext page

The following calculations are used in this test:

 

Deformation

 

The axial deformations can be specified directly or using deformation dial readings. When using dial readings they are converted to actual deformations using a dial constant.

 

Da = (Ra - Rai) * ADC                        

 

where,

Da        = Axial deformation

Ra        = Axial dial reading

Rai        = Initial axial dial reading

ADC        = Axial dial constant

 

 

Axial Load

 

The Axial loads can be specified directly or using readings from a load ring. When using readings from a load ring the readings are converted to loads either using load ring constants or a linear equation.

 

Load Ring Constant

 

If (R - R0) < Crossover        Pa = (R - R0) * LRC1                

 

If (R - R0) > Crossover        Pa = Crossover * LRC1 + (R - R0 - Crossover) * LRC2

 

Linear

 

Pa = M * (R - R0) + C

 

where,

Pa        = Axial load

R        = Load dial reading

R0        = Initial load dial reading

LRC1        = Load ring constant 1

LRC2        = Load ring constant 2

M        = Linear multiplier

C        = Linear constant

 

 

Axial Strain

 

εa = Da / hc        

 

where,

εa        = Axial strain

Da        = Axial deformation

hc        = Consolidated height of specimen

 

 

Deviator Stress

 

σd = Pa / A  - ΔσRM - ΔσFP

 

where,

σd        = Axial stress

Pa        = Axial load

A        = Cross-sectional area (see below)

ΔσRM        = Rubber membrane correction, only applied if greater than 5% of σd (see below)

ΔσFP        = Filter paper correction, only applied if greater than 5% of σd (see below)

 

 

Minor Stress

 

σ3 = CP - Pp

 

where,

σ3        = Minor stress

Cp        = Confining pressure

Pp        = Pore pressure, if not specified uses Bp

Bp        = Back pressure

 

 

Major Stress

 

σ1 = σd + σ3

 

where,

σ1        = Major stress

 

 

Peak Compressive Strength

 

Compressive strength = maximum σd

 

 

Saturated Volume

 

The calculation of the saturated volume will depend primarily whether the saturated diameter was specified and on the cross-section method selected.

 

Vsat = π * hs * ds2 / 4                                Saturated diameter specified

 

Vsat = V0 - ΔVsat                                ASTM Method A

 

Vsat = Vwater + Vsolid + ΔVcon                        ASTM Method B

 

Vsat = Vsolid + Vvoid + ΔVcon                        ASTM Method B with consolidated saturation estimate

 

Vsat = hs * [1 - 2*(h0 - hs) / hs] * A0                COE Uniform Strain

 

Vsat = Vsolid + Ms * wi - ΔVsat                        COE Saturation Assumed

 

where,

Vsat        = Saturated volume

Vsolid        = Volume of solids = Ms / (SG * ρw)

Ms        = Mass of solids = ρd * V0

A0        = Initial cross-sectional area = π * d02 / 4

V0        = Initial volume =  A0 * h0

Vwater        = Final volume of water = wf * Ms / 100

Vvoid        = Final volume of voids = (wf * Ms) / Sest

Sest        = Estimated percentage consolidated saturation

ΔVsat        = Saturated volume change

ΔVcon        = Consolidated volume change

hs        = Saturated height

ds        = Saturated diameter

wi        = Initial water content

d0        = Initial diameter

wf        = Final percentage water content

 

 

Consolidated Volume

 

The calculation of the consolidated volume will depend primarily whether the consolidated diameter was specified and on the cross-section method selected.

 

Vcon = π * hc * dc2 / 4                                Consolidated diameter specified

 

Vcon = V0 - ΔVcalc - ΔVcon                        ASTM Method A

 

Vcon = Vwater + Vsolid                                ASTM Method B

 

Vcon = Vsat - ΔVcon                                ASTM Method B with consolidated saturation estimate

 

Vcon = hc * [1 - 2*(h0 - hc) / h0] * A0                COE Uniform Strain

 

Vcon = Vsat - ΔVcon                                COE Saturation Assumed

 

where,

Vcon        = Consolidated volume

ΔVcalc        = Calculated change in saturated volume = 3 * V0 * (h0  - hs) / h0

hc        = Consolidated height

dc        = Consolidated diameter

 

 

Cross-sectional Area

 

A = Ac / (1 - εa)

 

where,

A        = Cross-sectional area

Ac        = Consolidated cross-sectional area = Vcon / hc

 

 

Rubber Membrane Correction

 

ΔσRM = 4 * Em * tm * εa / Dc

 

where,

ΔσRM        = Rubber membrane correction

Em        = Young's modulus

tm        = Membrane thickness

Dc        = Diameter after consolidation = (4 * Ac / π)½

 

 

Filter Paper Correction

 

ΔσFP = KFP * PFP / Ac                                For εa greater than 2%

 

ΔσFP = 50 * εa * KFP * PFP / Ac                        For εa less than 2%

 

where,

ΔσFP        = Filter paper correction

KFP        = Load carried per unit length of perimeter covered by filter paper

PFP        = Perimeter covered by filter paper = %C * P

%C        = Percentage of perimeter covered

P        = Perimeter of specimen = π * d0

 

 

Water Content

 

The calculation of the water content volume will depend primarily whether the saturated diameter is specified and on the cross-section method selected.

 

wi (%) = 100 * (Mbwt - Mbdt) / (Mbdt - Mbt)                Initial

 

wi (%) = 100 * [Mw - (Madt - Mat)] / (Madt - Mat)        Initial if Mbwt and Mbdt not specified

 

ws (%) = 100 * (Vsat - Vs) / Ms                        Saturated diameter specified

 

ws (%) = 100 * (Ms * wf + ΔVcon) / Ms                Saturated ASTM Method A and B

 

ws (%) = 100 * (wi - ΔVsat / Ms)                        Saturated COE Uniform Strain

 

ws (%) = 100 * (Vsat - Vsolid) / Ms                Saturated COE Saturation Assumed

 

wc (%) = 100 * (ws - ΔVcon / Ms)                        Consolidated ΔVcon specified

 

wc = wf                                                Consolidated ΔVcon not specified

 

wf (%) = 100 * (Mawt - Madt) / (Madt - Mat)        Final

 

where,

wi        = Initial percentage water content

ws        = Saturated percentage water content

wc        = Consolidated percentage water content

wf        = Final percentage water content

Mbwt        = Mass of tare and wet specimen before test

Mbdt        = Mass of tare and dry specimen before test

Mbt        = Mass of tare used before test

Mawt        = Mass of tare and wet specimen after test

Madt        = Mass of tare and dry specimen after test

Mat        = Mass of tare used after test, if not specified uses mass of tare before test

Mw        = Wet sample mass

 

 

Dry Density

 

ρi = Mw / V0 / (1+ wi/100)                        Initial

 

ρs = Ms / Vsat                                        Saturated

 

ρc = Ms / Vcon                                        Consolidated

 

where,

ρi        = Initial dry density

ρs        = Saturated dry density        

ρc        = Consolidated dry density        

 

 

Dry Unit Weight

 

γi = ρi * γw                                        Initial

 

γs = ρs * γw                                        Saturated

 

γc = ρs * γw                                        Consolidated

 

where,

γi        = Initial dry unit weight

γs        = Saturated dry unit weight

γc        = Consolidated dry unit weight

γw        = Unit weight of water (9.807 kN/m3)

 

 

Saturation

 

Si (%) = 100 * Vwi / Vvi                                Initial

 

Ss (%) = 100 * Vws / Vvs                        Saturated

 

Sc (%) = 100 * Vwc / Vvc                        Consolidated

 

where,

Si        = Initial saturation

Ss        = Saturated saturation

Sc        = Consolidated saturation

Vwi        = Initial volume of water in sample = (Mw - Ms) / ρw

Vvi        = Initial volume of voids = V0 - Vs

Vws        = Saturated volume of water in sample = [Vsat * ρs * (1 + ws/100) - Ms] / ρw

Vvs        = Saturated volume of voids = Vsat - Vs

Vwc        = Consolidated volume of water in sample = [Vcon * ρc * (1 + wc/100) - Ms] / ρw

Vvc        = Consolidated volume of voids = Vcon - Vs

ρw        = Density of water (1.0 g/cm3)

 

 

Void Ratio

 

ei = Vvi / Vs                                        Initial

 

es = Vvs / Vs                                        Saturated

 

ec = Vvc / Vs                                        Consolidated

 

where,

ei        = Initial void ratio

es        = Saturated void ratio

ec        = Consolidated void ratio